• If you are new to GiantScaleNews.com, please register, introduce yourself, and make yourself at home.

    We're 1st in Giant Scale RC because we've got the best membership on the internet! Take a look around and don't forget to register to get all of the benefits of GSN membership!

    Welcome!

Recent content by HuckinHavoc

  1. HuckinHavoc

    Bavarian Demon Cortex

    I do mine sitting on the tail and it is fine.
  2. HuckinHavoc

    48" Edge 540 Building, Flying, and Questions

    Started building mine last night. i fished some flat carbon fiber strips down there with dental floss and used a long tip to drip CA on them. looks kind of wack but no more flexing in the turtle deck when you squeeze the sides. I tried to save the original formers but they were too far gone...
  3. HuckinHavoc

    Bavarian Demon Cortex

    Flew my 48" Laser with the Cortex in it today. I have my gyro set up to remove the "hold" feature by copying bank 1 to bank 2. I set my bank one up at 30% to begin with and then found that was a little too much for me. At 30% I felt like my KE spins were flattening out on me. Ended up...
  4. HuckinHavoc

    Aerobeez 48" EPP Extra 330 Build

    That is really cool. I am going to have to give on of these a try once I wear out a 48"
  5. HuckinHavoc

    Aerobeez 48" EPP Extra 330 Build

    In the pictures it looks more like a balsa plane with EPP covering than a "foamie". Is that an accurate description?
  6. HuckinHavoc

    Bavarian Demon Cortex

    Luckily the program is really straightforward and easy to use. I was pleasantly surprised.
  7. HuckinHavoc

    Bavarian Demon Cortex

    The Laser has been Demonized, lookin seXah!
  8. HuckinHavoc

    Bavarian Demon Cortex

    Copied my bank 1 to bank 2. Super easy one click deal. I am going to put the gyro on the DX8 Aux3 knob like you guys are suggesting. Thanks for all the help, I can't wait to try it out in the air!
  9. HuckinHavoc

    Bavarian Demon Cortex

    Roger. I will be copying the bank 1 for 2 rate modes.
  10. HuckinHavoc

    Bavarian Demon Cortex

    My concern about the knob is that it goes past center (0 gain) so fast that if I had a problem with the gyro it would be hard to turn it off. I can see myself trying to get it off and swapping between bank 1 & 2 repeatedly before finding 0 gain. Your comment about setting one side to zero is a...
  11. HuckinHavoc

    Bavarian Demon Cortex

    I had it on my AUX3 knob but decided to take it off because I thought it would be too hard to find center (off) while flying. I like the idea though, just think it is too much workload for my skill level.
  12. HuckinHavoc

    Bavarian Demon Cortex

    Thanks I didn't realize I needed to copy the banks. I will try to figure that out tomorrow.
  13. HuckinHavoc

    Bavarian Demon Cortex

    GYRO What is suggestion for a starting point for gains? Mine went into a 48" Laser so I am guessing that it is going to be about the same as your Edge. I am not going to set mine up with a Hold mode, just normal and "high wind".
  14. HuckinHavoc

    Bavarian Demon Cortex

    Already had the latest firmware version, lol. I was able to change the servo type from analog to digital. Into the plane it goes!
  15. HuckinHavoc

    Bavarian Demon Cortex

    Plugged it up like it was going into the airplane (external power) and it fired right up. Thanks for the help, I didn't want to plug it into external power and the USB and possibly over volt it or something.
Top