• If you are new to GiantScaleNews.com, please register, introduce yourself, and make yourself at home.

    We're 1st in Giant Scale RC because we've got the best membership on the internet! Take a look around and don't forget to register to get all of the benefits of GSN membership!

    Welcome!

Search results

  1. TonyHallo

    Scale 18% De Havilland DHC-2 Beaver by MR Aerodesign

    Just ordered two sets, thank you WMcNABB
  2. TonyHallo

    Scale Wendell Hostetler 30% Piper Cherokee Glass Fuselage Build.

    The stabilator linkage is complete, rather than a heavy duty rod end, I used a fitting from a DuBro heavy duty adjustable control horn. Here's a short video.
  3. TonyHallo

    Scale Wendell Hostetler 30% Piper Cherokee Glass Fuselage Build.

    Have the stabilator coped out and laid 2 layer of carbon fiber on the foam. Ready to cut the anti servo tab loose. Also finally finish the bottom door hinge. Started laying out the stabilator control linkage as well. The servo will be mounted on the front side of the rear former. A Rocket...
  4. TonyHallo

    Scale 18% De Havilland DHC-2 Beaver by MR Aerodesign

    That a good tip!
  5. TonyHallo

    Scale 18% De Havilland DHC-2 Beaver by MR Aerodesign

    What are the weights in photo 3136?
  6. TonyHallo

    Scale Nelitz 1/3 scale Cub build

    That patch will stare you in the face forever.
  7. TonyHallo

    Scale 18% De Havilland DHC-2 Beaver by MR Aerodesign

    Welcome back WMcNabb, it's been a while since you posted.
  8. TonyHallo

    Scale Wendell Hostetler 30% Piper Cherokee Glass Fuselage Build.

    The stabilator bearing is near completion. There is very little clearance but the tube turns freely, vacuum bagging the socket is the way to make great fittings sockets. The stabilator rattled around a little on my two previous Cherokees, this one will not.
  9. TonyHallo

    Scale Wendell Hostetler 30% Piper Cherokee Glass Fuselage Build.

    The linkage is Rocket City strip aileron linkage. The clevis just snaps onto knuckle, it is stiff, need to use a screwdriver to bend it open to get it on, it's not coming without a screwdriver. They made great linkages fittings, fire in their factory closed them down in the early 2000's. I...
  10. TonyHallo

    Scale Nelitz 1/3 scale Cub build

    You better get busy!
  11. TonyHallo

    Scale Wendell Hostetler 30% Piper Cherokee Glass Fuselage Build.

    Laid out a perpendicular bisector on top of the bench with a large compass, the plane was aligned to the line and vertically plumbed. The tube supports plates were drilled together so that they are same height. A short piece of socket was laid up with carbon powder added to reduce friction...
  12. TonyHallo

    Scale Wendell Hostetler 30% Piper Cherokee Glass Fuselage Build.

    Clear packing tape installed on the top half of the tail cone. The joint was painted with PVA after the tape was placed. Decided to go with 3 layers of 4 ounce cloth for the flange. The flange will get trimmed to 3/8" once cured. The rudder is back on with new hinges and the bearing block...
  13. TonyHallo

    Scale Wendell Hostetler 30% Piper Cherokee Glass Fuselage Build.

    Had to break out the vacuum pump as I have no means to control the vacuum on the new pump. Looks like a winner so far, of course so did the prototype! The skin is covered with parchment paper as the Gorilla bleeds through where there are pin holes. The skin is 1 1/2 ounce glass and 5.7 carbon...
  14. TonyHallo

    3D Pitts 12S

    Google JTEC EXHAUST is Shutting down and see page two
  15. TonyHallo

    3D Pitts 12S

    I would image since it is a motor box it is square, you are missing the floor, the top should be the same width? I would also image it tabs into the sides so the minimum length would be to last tab hole, make it longer if you like, cut it out later if necessary.
  16. TonyHallo

    Scale Nelitz 1/3 scale Cub build

    Great idea
  17. TonyHallo

    Scale Wendell Hostetler 30% Piper Cherokee Glass Fuselage Build.

    Have the foam core cut and the socket is installed. The first skin is in the bag, just might get is joined tomorrow, hopefully the second skin will get laid up tomorrow. The relief grooves for the corrugations are cut in the core
  18. TonyHallo

    The 'What did you do in your workshop tonight?' thread

    What program are you using?
  19. TonyHallo

    Help! Mystery plane

    My experience is that the needle valve is the first thing to go so plan to place it as well, It is part of the kit. The carb for the photo above is a Walbro WA 58 and takes a K10-WAT kit. You can find a kit most anywhere.
  20. TonyHallo

    Scale Wendell Hostetler 30% Piper Cherokee Glass Fuselage Build.

    After further review, I plan to cut the airfoil out of 1 pound expanded bead with a 1/2" 2 pound trailing edge. The weight was not sufficient to make the skins flat and the ribs are telegraphing through. This way I attach the skins under vacuum. Oh well, make another socket and set of skins...
Top