• If you are new to GiantScaleNews.com, please register, introduce yourself, and make yourself at home.

    We're 1st in Giant Scale RC because we've got the best membership on the internet! Take a look around and don't forget to register to get all of the benefits of GSN membership!

    Welcome!

Search results

  1. A

    Ignition - off topic

    Actually, I think it was wrong way rc. Just saw their ad.
  2. A

    Ignition - off topic

    I had posted some questions on this forum about building a Velox. There was a lot of discussion about engine selection... Somewhere in the thread(s) there was some discussion about replacement ignitions. I have a Brison 2.4 in a Cap232 that I am struggling with. I've had ignition trouble...
  3. A

    35CC 3D Plane

    Between all of the baseball games I finally got the 35cc Velox fully assembled, balance and running. That 35 is impressive.
  4. A

    35CC 3D Plane

    This is what I ended up with for a switch. It's one of the two toward the bottom of this page It's just a simple 10amp switch. http://electrodynam.com/rc/usw/index.shtml The guy that designs and manufactures these is a member of the club I belong to. He holds a masters degree in...
  5. A

    35CC 3D Plane

    In their contact info, it was just funny the way they stated it. If you're counting on an immediate call back... this ain't the place . I'm debating still. There is a local place, electrodynamics, that sells 10amp switches. I'm sure that would be sufficient. I do like the Badger though. I...
  6. A

    35CC 3D Plane

    Check contact information on their web page. Don't count on is getting back to you in the same week... at least they're honest.
  7. A

    35CC 3D Plane

    Wire gauge on Fromeco switches? I went out and looked at the Badger switch. They want a hefty up charge for Deans connectors. Do you get the same gauge wire n the JR connectors as the Deans?
  8. A

    35CC 3D Plane

    Something to think about. If you place you ignition battery too close to your receiver (Horizon Hobby claim no closer that 12") the radio frequency from the battery will significantly shorten the range of your radio. I experienced this first hand on a build last year. I did a distance check...
  9. A

    35CC 3D Plane

    It's functionally the same as an opto kill switch and a BEC together. It's just integrated into one unit. My flying buddy swears by the other setup. I have opto switch, the BEC and capacitors. I'm still debating what to do.
  10. A

    35CC 3D Plane

    I'm not sure I care about redundant batteries. I just see a 5 amp switch as problem waiting to happen. They eventually wear out. It look like these fromeco switches are pretty durable.
  11. A

    35CC 3D Plane

    So if I am reading you right, I could use one switch (Badger). Then after the switch, use a regulator to the ignition with an opto kill switch and run straight voltage to the receiver.
  12. A

    35CC 3D Plane

    I looked at that wolverine. I want to regulate my ignition, but not my servos. Will that switch allow what I want to do?
  13. A

    35CC 3D Plane

    I have everything in the plane but batteries switches and the associated wiring. I have 1 4500mah 2s battery sitting on the tail. Im still debating what lipo configuration to use. In the past I have run two regulator off of one battery. I've heard the ignition last longer on lower...
  14. A

    35CC 3D Plane

    I'm going to leave the engine as-is. I've barely had the time to put this plane together. I'm going to have limited time to fly it this year. I have to finish it. I bought a black plastic 3" Great Planes spinner. Just can't finish it without a spinner. I'll be balancing soon.
  15. A

    35CC 3D Plane

    You best break-in will always be on a freshly honed cylinder. So either I'm doing like you did or probably forget it. I had not heard of the reed valve thing. Do you have any info?
  16. A

    35CC 3D Plane

    I have not put a Bowman ring in this engine. If I put it in at all, I want to put it in before break-in. I bought one for my DLE20, but haven't put it in yet. I really don't know if it makes a big difference. What is you mileage on the subject?
  17. A

    35CC 3D Plane

    I thought 20x8 was a bit much. Thanks. I'll drop that back. I'll probably still use a Xoar until I've got some time on this plane. This may sound a little paranoid, but I nosed over my plane a couple of time last year because the grass on the field got caught on the wheel pants. I've gotten...
  18. A

    35CC 3D Plane

    I wasn't even going to ask the question. Glad I did. I had no idea about the EF spinner. Actually, 3DHS sells EF spinners. So the color might be pretty close on the red. After looking at my cowl again, yellow might work if I can find the right color of yellow. I might just fly it with a...
  19. A

    35CC 3D Plane

    Spinner or no spinner? I really don't want to add more weight than I have to on the front of the plane, so I was looking at a plastic spinner or maybe carbon fiber. In plastic, only black or white match. I don't think either one would look right. Aluminum would look sharp, but too heavy...
  20. A

    35CC 3D Plane

    A Little Upate (Pics) The plane is coming along slowly, but nicely. I was sick all last week and lots of little league baseball. Still not 100% and games start tonight. I'm not sure when I will get to fly this little beasty. Good news is I did get some work done on it last night. Cowl is...
Top