• If you are new to GiantScaleNews.com, please register, introduce yourself, and make yourself at home.

    We're 1st in Giant Scale RC because we've got the best membership on the internet! Take a look around and don't forget to register to get all of the benefits of GSN membership!

    Welcome!

Search results

  1. U

    20cc Sbach

    I don't want to open a new thread but i'm "eyeballing" this class too but i was oriented to the Edge 540 20cc. My 55-60cc version fly so good that i for my father i was thinking abvout this little one. Any flight report on this? Also which is the ideal configuration for this class apart of the...
  2. U

    Aeroplus 60cc / 92" Edge 540 V3 from Limitless Aero

    No i was meaning low and high needles on carb. Sorry. Anyway i fly the plane again without weight (only weight add was equal to the cowl),and it is really a blast!!! Very easy on all manouvers and great control authority.
  3. U

    Aeroplus 60cc / 92" Edge 540 V3 from Limitless Aero

    Yes I have done the linkage that way. For the TH curve well I have a Taranis and before a 9XII so no problemi, already tried, but I am not sure there is a rule for having a right curve... For the engine which is the right way to fine tune min max on carb? Thanks for help guys ;)
  4. U

    Aeroplus 60cc / 92" Edge 540 V3 from Limitless Aero

    Thanks Gyro i will try without weight than. Can someone point me to a tuning for dummies or some simple steps to do to be sure the engine is well tuned? I'm asking this because at my small field there aren't many people using gas plane and no one have big experience with 50cc aircraft...
  5. U

    Aeroplus 60cc / 92" Edge 540 V3 from Limitless Aero

    Yesterday finally i have maidened mine. It was long time it was ready but for job and bad weather on all week ends... it was there on the floor of my garage. I put 1 Kg on the front to achieve the cog a little in ront of the wing spar. Well i was with no cowl (about 360gr) so the real weight...
  6. U

    Aeroplus 60cc / 92" Edge 540 V3 from Limitless Aero

    But if the plane in really tail heavy i have doubt i can land it in one piece... Stephen from Aeroplus has replied to me that he will check with his pilots. If anyone has a useful range of CoG just for the maiden it will be super.
  7. U

    Aeroplus 60cc / 92" Edge 540 V3 from Limitless Aero

    I'm quite ready for the maiden but i have doubt about the cog. On mine it is very difficult to have the cog on the wing tube the plane is really tail heavy. My setup is this: DLE-55 on stock muffler Xoar 23x8 wood prop Savox 1257 for throttle Savox SV-1272 on all surfaces 2x 2s lipo 1600mah for...
  8. U

    Aeroplus 60cc / 92" Edge 540 V3 from Limitless Aero

    For the rudder pull-pull rods assembly i have used the cross setup i have chose the right way? I'm asking this because my rods are quite strength at center but when i'm at full travel i had the rods quite sloppy so i was thinking if this will be a problem or if the air pressure will minimize the...
  9. U

    Servo setup: EPA, current, and linkages

    Ok Thanks as i did. To be more clear for match or balance feature do you mean a special feature of the radio so that if i give some subtrim it will auto correct the two limits so that both sides have equal throw? I have the Frsky Taranis and it has this feature but it is more suited if you have...
  10. U

    Servo setup: EPA, current, and linkages

    Returning to the topic of servo setup i have some questions, since i have learned something new reading the Joe Smith posts about MAX EPA and Amp draw. In a new plane: 1- Set the control horn almost at 90° from servo and linkage for a better geometry. To do so if some sub-trim is needed how do...
  11. U

    Aeroplus 60cc / 92" Edge 540 V3 from Limitless Aero

    Yes of course direct with 2x 2s 1600mah lipos on Jeti DPS-40 switch
  12. U

    Aeroplus 60cc / 92" Edge 540 V3 from Limitless Aero

    So to remove the rudder you have to remove remove or un-screw the tail gear?
  13. U

    Aeroplus 60cc / 92" Edge 540 V3 from Limitless Aero

    Hello i have my kit quite ready for the maiden. I need some advice for the removable rudder. How do you fix the bar? I have to do a "L" shape on the top rudder exit and fix with some clear tape and leave the bottom part near landing gear straight? This is my first plane with the removable...
  14. U

    New Here? Introduce yourself!

    Yes i was considering it also but there isn't many info or feeedback about it yet.
  15. U

    New Here? Introduce yourself!

    Thanks guys for the wellcome!! Well I'm from Italy, i have some electric profile planes like Mojo MoAss 60 and Fusion 90 X3D with which i have a lot of fun!! I have less experience with gasser i had a Godwing MX2 50cc v2 but i never liked it because it was a "faulty" airframe and in few words...
Top