• If you are new to GiantScaleNews.com, please register, introduce yourself, and make yourself at home.

    We're 1st in Giant Scale RC because we've got the best membership on the internet! Take a look around and don't forget to register to get all of the benefits of GSN membership!

    Welcome!

Search results

  1. B

    Engine Gurus Unite -> I need HELP!

    Should they hold water?
  2. B

    Engine Gurus Unite -> I need HELP!

    49dimes --> I looked around for an article or thread on the best way to de carbon the engine but didn't see much. Anyone have a good link? Thanks Bob
  3. B

    Engine Gurus Unite -> I need HELP!

    What do you see in the first picture? Should the reeds hold water as a measure of whether or not they are sealing properly? Frank is out of 30 rings right now, so I'm going to true the block and run it just to see what happens. Thanks Bob
  4. B

    Engine Gurus Unite -> I need HELP!

    Here are a couple of bad pictures of my reeds. They don't appear to be chipped or cracked. They do not hold water though. Should they? I'll true up the reed block while waiting for new parts. I haven't replaced the fuel lines yet. They appear to be functioning as they should, and are not stiff...
  5. B

    Engine Gurus Unite -> I need HELP!

    I do have another ignition I can try. I'll do that first. I'm getting a Bowman, some new gaskets, a reed block and new reeds. We'll eat this cow one burger at a time. It starts great, and will reach peak rpm fine. It just won't hold peak. Just sags off and dies. The transition is crap though...
  6. B

    Engine Gurus Unite -> I need HELP!

    Gary --> I cleaned and rebuilt the old carb and there was no change at all. Still couldn't adjust the low end enough to get the four stroking out. Installed the new carb and there was no change. Engine acted exactly as before. Can't adjust out the four stroking on the bottom, can't get rich...
  7. B

    Engine Gurus Unite -> I need HELP!

    Scenario is DLE 30 about 4 years old. I didn't buy it new, and I don't fly it a lot, but lately here's the scoop. Very rich on the low end no matter where the needle is. If the needle is too far closed it dies. Runs very rough on the low end and spits out black junk because it's four stroking...
  8. B

    Need a Walbro for my DLE 30 )--:

    Put the new 645 on and is same ole same ole. I'm a gonna start a new thread. I need ideas, bad...
  9. B

    For Sale Edge Reduction Sale LPU SD

    I wish the board showed location for the sender :oblong:
  10. B

    Need a Walbro for my DLE 30 )--:

    I found a couple of new carbs in the shop that I had when I owned a Syssa. They have the same venture diameter of @ 15.87mm so I'm thinking about giving them a try. One is an 813A, and one is a 645. Any thoughts on a preference on one over the other? Does anyone know how I can determine if...
  11. B

    Need a Walbro for my DLE 30 )--:

    Capt.Roll --> Where do you see carbs on the MileHigh site?
  12. B

    Need a Walbro for my DLE 30 )--:

    Thanks Like Scott says, there's no listing for a 3o on the Valley View site, but I may call them. I'll try Milehigh too. Take care Bob
  13. B

    Need a Walbro for my DLE 30 )--:

    My DLE carb took a dump. Anyone know the Walbro equivalent for the DLE 30? Help! Thanks Bob
  14. B

    3DHS 91" Yak 55

    Yes I can. There are several 3DHS planes at our field with this happening. Oh well...
  15. B

    3DHS 91" Yak 55

    A local club member here ins South Jersey has one for sale. I think he'll let it go at a very reasonable price. He just got another plane and is taking the gear out of the Yak. Take care Bob
  16. B

    SOLD! --> SOLD <-- AeroFLy Pro Deluxe Platinum Edition with Interface

    Not sure where to put this, so please move it if necessary. AeroFLy Pro Deluxe Platinum Edition with Interface $35 not including shipping. If the buyer can pick up, or meet me somewhere, I also have the machine this runs on. It's windows 2000 and runs it fine. Thanks Bob
  17. B

    SOLD! ParkZone Visionaire -> Nearly New!

    ParkZone Visionaire Near New No crashes or dings. AS3X Removed so no receiver No Motor or Speed Controller I have the original servos but they are not installed. Will travel a little in Pa,NJ,Del if the price is right. Cannot Ship! Plane only, no servos, no receiver $65
  18. B

    Joe Smith quits 3DHS!

    Subscribed
  19. B

    Anyone Here Flying Ultra Micro?

    I'm looking for information on the brushless conversion for my UMX Extra from Parkzone.Anyone know about it, or what it takes to go from the AR6400 to a brushless conversion if that's possible. Also, what's the latest and greatest in batteries for this size plane these days? ThanksBob
  20. B

    Looking for 3S 2250 sized Aeroabtic Plane to replace...

    I ordered the EF 300 EXP Should be here tomorrow 10/15   Thanks all Bob
Top