• If you are new to GiantScaleNews.com, please register, introduce yourself, and make yourself at home.

    We're 1st in Giant Scale RC because we've got the best membership on the internet! Take a look around and don't forget to register to get all of the benefits of GSN membership!

    Welcome!

Search results

  1. 49dimes

    The I'm going out flying thread 2016

    Too much summer bummer heat going on down here but I Give "Two Cheeseburgers Up" to Joe and Tanner! NOW THAT'S WHAT I CALL A BUILD!
  2. 49dimes

    Peak Models 32% Extra 330 SC

    Hey! What are good buds for anyways!? :cautious:. To be honest:cautious:.....When I look at those two beautiful boo:oops:....I mean burgers.....I get hungry all over again:rolleyes:.
  3. 49dimes

    The 'What did you do in your workshop tonight?' thread

    Yep! The 18 buck header has been on my Edge almost 6 years.
  4. 49dimes

    The 'What did you do in your workshop tonight?' thread

    I Just signed on but got to go take care of sumtin.......Look At HK. @stangflyer might have his for sale if he still has it. Will post a link a bit later bro.
  5. 49dimes

    Peak Models 32% Extra 330 SC

    The dime does get shared around my place ;).
  6. 49dimes

    Peak Models 32% Extra 330 SC

    Two of the six BLS H50B's are on their way back:)however I just sent the other 4 back to get "updated":blank:. The 330 sets a little naked right now. Once All my servos are back it will get an Aura to boot with the i10. @ChickenBalls in the "mean" time I've been building these colossal...
  7. 49dimes

    The 'What did you do in your workshop tonight?' thread

    I ran a pitts (Slimline) for a bit and made no more power than the stock muff. The cost of a pro flow is high but you can get a nice China can for half the cost and it does the same thing. Really helps smooth the air flow through the engine and cleans up a muddy midrange so you can get a really...
  8. 49dimes

    The 'What did you do in your workshop tonight?' thread

    DLE 55 with a stock muffler and 23x8 will pull 16.5 to 17.5 pounds out of a hover with authority but not ballistic. I had one (DLE 55) on a YAK 54 (Korean made off brand) that weighed 19 pounds and it was like pulling a log up. Put a pro flow on it and it pulled the log up with authority.
  9. 49dimes

    Electric Pilots.

    I got some Turnigy motors and speed controls for Cheaper than Cheap that are basically brand new. G32 or the NTM 42 The G32 600kv or NTM 42 750kv would haul the LT 25 VERY nicely. I personally bought them to test their quality when I decided to do a couple of nice electrics. I went with the...
  10. 49dimes

    Electric Pilots.

    I thought I was never going to read you again! Good to read you MIKE :shake:.
  11. 49dimes

    GSN Admin

    I used to haul like that in an old beat 92 for Ranger. I had a electric MX extra from PA get sucked right out of it after a bigger delivery truck blew past me. Just As I realized what happened I looked in the rear view to see a older station wagon finish it off :face-palm:.
  12. 49dimes

    Scale 50cc Scratch Build From My Own Design Revisited

    LOVE that show room finish!!!:attaboy:
  13. 49dimes

    GSN Admin

    HEY!!! I drive a soccer mom van :woohoo!:. And it can carry lots of balls!!!!! lol Oh!.......and cheeseburgers!
  14. 49dimes

    Making a few Changes

    This new admin guy........Well......I think he knows how to make a really good cheeseburger :attaboy:.
  15. 49dimes

    Gyro's for planes

    I do not know what your Tx Rx set up is but it does not matter because in order to reverse your servos you must choose the "custom" transmitter option. Prepare your transmitter as directed. Using the Aura tool.....Under the "File" tab select "New Aura Config File". There is where you see the...
  16. 49dimes

    Post your foamies you’re flying

    Been flying the QQ300 too @ericb . It's a hoot!! My cheap HK plane.......well at least the wheels live on in my MXS
  17. 49dimes

    CNC machining your own parts

    Dremmel and Xacto . That's all I got :(. Well.......my fingers too. But they are a bit worn out these days. Helped a buddy build a cnc router system with stepper motors so we could spit out small flat foam board planes. Used a dremmel tool as the router.
  18. 49dimes

    Big Electric plane show and tell

    The pic with the planes reflection in the standing water is :cool: @Express
View older results
Top