• If you are new to GiantScaleNews.com, please register, introduce yourself, and make yourself at home.

    We're 1st in Giant Scale RC because we've got the best membership on the internet! Take a look around and don't forget to register to get all of the benefits of GSN membership!

    Welcome!

Search results

  1. AKNick

    Scale 20cc DHC-2 "Beaver" Kit Build from Moustache Model Works

    Control rod guide tubes installed. Mine ended up 25mm fwd of the fwd blind nut, and about 7.5mm from the edge of the lower ply skin. I ended up with a gap in the exit holes and used UV glue to fill it. Set in place with CA as it doesn’t bind to the tube that well. Elevator and rudder bulkhead...
  2. AKNick

    Scale 20cc DHC-2 "Beaver" Kit Build from Moustache Model Works

    Painted the canopy hatch and seats/servo covers. Note that I added a little gusset in the hatch lower corner for some added strength as it wasn’t a very tight joint without glue. Got the door fuselage magnets in place. Would have been easier to align all of them with the doors in place. Also...
  3. AKNick

    Scale 20cc DHC-2 "Beaver" Kit Build from Moustache Model Works

    LOL!! Just needed a shot with something round up front!! My bad!
  4. AKNick

    Scale 20cc DHC-2 "Beaver" Kit Build from Moustache Model Works

    Cowl and WingTips are Fiberglass. It will be covered in ultracote. Thanks guys!!:D
  5. AKNick

    Scale 20cc DHC-2 "Beaver" Kit Build from Moustache Model Works

    My final post for the night and it’s a good one too. It has been one exactly one month since I have started this build. So here is a photo of everything together that I have accomplished in four weeks!!! Wow! Ok ok, I’ll get the cowl too! Please note the 1lb bottle of Lysol is not...
  6. AKNick

    The 'What did you do in your workshop tonight?' thread

    Been putting together a Funtana 90S for a buddy in between working on the DHC-2. Coming out super tail heavy. So I added .4lbs to the nose.... eeeekkk!!! Not only that but the covering was old,peeling off, Hangar rash like a cat got it, cracked canopy... missing parts!!! Lions tigers a bears...
  7. AKNick

    Scale 20cc DHC-2 "Beaver" Kit Build from Moustache Model Works

    Seat/Servo cover Assembly. I did find this part fun. Kind of a no-brainer... BUT I have to love the engineering that went into this. Since I used to work on the full scale DHC-2 I remember having to frequently remove and install the rear seats to accommodate lots of cargo. They interlock into...
  8. AKNick

    Scale 20cc DHC-2 "Beaver" Kit Build from Moustache Model Works

    Manual has you bevel the horizontal mount plate to match the airfoil. Awe look a heart I’m guessing the manual wants you to use scrap balsa grain forward. But I decided to use a single sheet from my stock and to parallel to the tube. Slight bevel Boom Canopy/hatch assembly
  9. AKNick

    Scale 20cc DHC-2 "Beaver" Kit Build from Moustache Model Works

    Fitted and glued in the lower aft corner skins. They fit pretty nice, I had to wet one to get it to make the bend without cracking. The fuselage top corners is part of a balsa tree. You start by sanding the plywood sides to match the bulkhead bevel. Took a while. I need some heavier grit...
  10. AKNick

    Scale 20cc DHC-2 "Beaver" Kit Build from Moustache Model Works

    It was thoughtful and I though down right cool for them to supply you with preformed sheet ply to go around the belly corners.... well mostly... all of mine were cracked. Could have been from shipping I’m sure. Not a big deal, a little bit of CA and it was fixed. The manual has you measure...
  11. AKNick

    Scale 20cc DHC-2 "Beaver" Kit Build from Moustache Model Works

    installed blind nuts for the tailwheel mounting bracket. Fit like a glove. Made sure they didn’t bottom out by tapping them into a slightly larger hole below the board it’s on. They nestle into the lower fuse frame and everything just fell into place beautifully. I wetted the sides to allow...
  12. AKNick

    Scale 20cc DHC-2 "Beaver" Kit Build from Moustache Model Works

    My thoughts exactly. Tail and wings need to be perfect. Thanks guys, I’m hoping everything else should be smooth sailings from here
  13. AKNick

    Scale 20cc DHC-2 "Beaver" Kit Build from Moustache Model Works

    Well this was a major pain in the butt. I ended up tearing the top skin off after seeing the planes lower skin was aligned and when twisting the top skin into place it would enhance the twist. After conversing with other people who are building this model found they had similar issues. They all...
  14. AKNick

    Scale 20cc DHC-2 "Beaver" Kit Build from Moustache Model Works

    I am a little stuck. Cannot get rid of some wicked frame twist. I don’t understand how it could be this bad. Everything has been taped, twisted by hand and taped, the only thing that gets rid of most of it if I don’t have the top skin on. Then I can twist the tail level to the wing tube. I’m...
  15. AKNick

    Scale 20cc DHC-2 "Beaver" Kit Build from Moustache Model Works

    @David Eichstedt Are these kits Serial #'d ? Just curious - Thanks!
  16. AKNick

    Scale 20cc DHC-2 "Beaver" Kit Build from Moustache Model Works

    Photo dump! Here is the reason once again to wait to glue the BLKHD #1 in place until the Fuselage side are in. I was able to cut the slot open and reglue it in place. Cabin support Beams in place Wing Tube fitted, added some 30min epoxy to the tube right before it enters the cutout...
  17. AKNick

    Scale 20cc DHC-2 "Beaver" Kit Build from Moustache Model Works

    Comic relief during this build is a nice moustache laser etched into the cross beam. So when you open the canopy this is revealed every time. Love it.
  18. AKNick

    Scale 20cc DHC-2 "Beaver" Kit Build from Moustache Model Works

    Here is a pic of me not following directions an pictures. This fuse skin need to fit inside the doubler #1. Bunch of visual progress on the fuselage. Looking back I wouldn’t use epoxy on the whole motor box assembly. It was frustrating to clamp and ended up not having very tight joints. If...
  19. AKNick

    Scale 20cc DHC-2 "Beaver" Kit Build from Moustache Model Works

    :attaboy: Welcome to GSN David!!!
  20. AKNick

    Scale 20cc DHC-2 "Beaver" Kit Build from Moustache Model Works

    On MMW blog on the website there is an addendum to the early kits where the tailwheel steering tube holes in the bulkhead are too small. Sure doesn’t leave a lot of material!
Top