• If you are new to GiantScaleNews.com, please register, introduce yourself, and make yourself at home.

    We're 1st in Giant Scale RC because we've got the best membership on the internet! Take a look around and don't forget to register to get all of the benefits of GSN membership!

    Welcome!

Search results

  1. Dan767

    150-200cc Extra 300SP

    I made my own, using the crimper and connectors in Japan 3d's post.
  2. Dan767

    PAU Extra 300sp 50cc

    Yes you can! Flew mine with a DLE 55, flew just fine. Really enjoyed this plane, only sold it to fund a 42% PAU Extra 300 :)
  3. Dan767

    3D Viper 120cc ARF is HERE!!!!!

    Sam, Check the dimension from the rear of the engine to the back of the thrust washer on the 3W. I think it's too long for the Viper.
  4. Dan767

    Regulator info needed

    They are adjusted by shorting the pins on the side of the regulator. Short the pins together with a small screw driver, and each time you remove the screwdriver it will increase approximately .2 volt. Once you get to the max output voltage it will reset to the lowest voltage. Max out is just...
  5. Dan767

    3D Viper 120cc ARF is HERE!!!!!

    I have one and it works great. Easy to use, highly recommend it!
  6. Dan767

    3D Viper 120cc ARF is HERE!!!!!

    Hmmm, for some reason it came up as in the UK. My apologies!
  7. Dan767

    3D Viper 120cc ARF is HERE!!!!!

    He's in the UK
  8. Dan767

    70cc PAU Extra 300SP build...

    Looks great Terry. I really enjoyed mine and at times wish I still had it.
  9. Dan767

    Futaba 18SZ

    And after that's done we go fly big birds! :adore: :applause: I'd like to compare it to my 18MZ as well.
  10. Dan767

    If you had $1000.00 to spend on a charger and power supply, what would you buy?

    www.progressiverc.com here in Washington state. Excellent company uses iCharger and can pretty much customize anything you might want. Had them do a 500 watt unit for me, excellent setup and support.
  11. Dan767

    Futaba 18MZ/14SG/8FG Tips and Tricks

    Are you using the Ailevator function? I found it easier to match mine using this set up. I've not had much luck getting them to be even slaving one to the other.
  12. Dan767

    Ordered my Su-26

    Did you disable the printer settings before you printed the template (fit to page etc.)?
  13. Dan767

    150-200cc Extra 300SP

    Very Nice!
  14. Dan767

    Wire tensioners

    Here: http://superstitionhobbies.com/collections/secraft/rudder-pull-pull-system_tensioner If you use theses, be sure and tighten them, otherwise it just strips the plastic coating off the cables and you only have a rudder that goes one direction. Not that I would know :adore:
  15. Dan767

    Has anyone ever tried towing banners with RC planes?

    AKA RCBugman on RCU and flew a lot of 3W'S?
  16. Dan767

    PAU 50cc Su-26

    My concern was whether you would be using less than 6 volts. It'll be fine, with the setup you've chosen. 6 volts gives you 139 in oz. of torque on the elevators and ailerons and that's just fine. You'll enjoy the plane, no doubt.
  17. Dan767

    PAU 50cc Su-26

    The S9402 is an older servo, it's the only one that I would think of changing. If you said what batteries you're using I missed it. If you use a 6v. setup you should be fine. Dan
  18. Dan767

    RIP Azhar from Aztech Aeromodels

    You're welcome!
  19. Dan767

    RIP Azhar from Aztech Aeromodels

    Azhar and I tried to get together a few times while we were both in Singapore or China. We were both in Singapore, I had sent him a text while I was very tired. Later, I re-read my text wondering how he made any sense of it. It was a good laugh later. We were discussing the difficulty in...
  20. Dan767

    Help picking out a prop for DA-150 ? !!

    Falcon or Mezjlik 32X10 will also work.
Top