• If you are new to GiantScaleNews.com, please register, introduce yourself, and make yourself at home.

    We're 1st in Giant Scale RC because we've got the best membership on the internet! Take a look around and don't forget to register to get all of the benefits of GSN membership!

    Welcome!

Search results

  1. TonyHallo

    Scale 20cc Edge 540 Profile “The Glitter”

    I must be lucky, I have not of these problems at the local Staples.
  2. TonyHallo

    I’m going out flying thread 2019

    I got a bunch of reference photos as well for future use, it's not often to get to mill around a bunch of full scale airplanes. There was a Citabera there that is very similar to Champ, I was wondering how I might do the fabric around the stabilizer, now I know.
  3. TonyHallo

    Scale Byron Glasair Build

    The left side window and the firewall bolts on, the bottom is clean. I plan to install the radio gear behind the firewall. The left side window is access for the spar through bolts.
  4. TonyHallo

    Scale Byron Glasair Build

    Thank you for your compliments. Both windows are glued in. Used pairs of magnets to hold the windows in place while the 560 canopy glue dried. Just found out that the grandsons wouldn't be here until 11:30 tomorrow, just might get the windows cleared before they arrive.
  5. TonyHallo

    I’m going out flying thread 2019

    Here are photos on the Cessna 310 that the local EAA is restoring for the airport. Two years ago and today. They are making progress. If i'm not mistaken, this plane belonged to Jimmy Stewart.
  6. TonyHallo

    I’m going out flying thread 2019

    The indiana Flyers Club and the Murrysville Area RC club flew demonstration flights both yesterday and today at the Jimmy Stewart airshow at the Jimmy Stewart Airport located in Indiana PA. I manged to get three flights in. We had two 15 minute periods each day during the air show between the...
  7. TonyHallo

    Scale 20cc Edge 540 Profile “The Glitter”

    What? The printers don't work in Canada? Or is it a cost thing?
  8. TonyHallo

    Scale 20cc Edge 540 Profile “The Glitter”

    I get my prints at Staples, I think they can print any size you want, reasonable price as well, not as cheap as printing at work but close. Small price to pay for retirement!!!!
  9. TonyHallo

    Scale Byron Glasair Build

    I already had the colors on hand from a previous build and have no way to cut vinyl. Since I retired my time is free!!!
  10. TonyHallo

    Scale Byron Glasair Build

    Finally got the clear on. The next time I will paint the strips first, then the white and right to clear. I wasted a lot of time masking each strip. Glue in the side window and windshield and give them a clear coat and final assembly can begin.
  11. TonyHallo

    Scale 20cc Edge 540 Profile “The Glitter”

    Once you make and use a glass tube, you never go back to phenolic tubes. They fit so much better.
  12. TonyHallo

    Scale 1/3 Scale Extra 330L Build.

    Check out flex seal at the local hardware store!!!!!
  13. TonyHallo

    Scale Byron Glasair Build

    This is a fiberglass fuselage, so there is no wood involved. I used a white base primer then dusted on self etch green spray bomb primer and and proceeded to sand my brains out. The layup is very lightweight so sanding on the flat areas where there are no former was a problem, couldn't push on...
  14. TonyHallo

    Scale Byron Glasair Build

    Today the white base coat was applied after a day of guide coat wet sanding. May get the yellow strip on tomorrow if things go according to plan. Thankfully the yellow, orange and red Monokote matching base coat paints are still good. I believe I bought the colors in 2005!
  15. TonyHallo

    Scale Byron Glasair Build

    I find the Open TX very powerful, no limits.
  16. TonyHallo

    Scale Byron Glasair Build

    Hope to see you Randy at your Fun Fly this year.
  17. TonyHallo

    Scale Byron Glasair Build

    It was a car I always wanted, V8 Vega. When I drive it today most people don't have a clue what it is. The engine install was rather easy, I used stock Monza mounts for the engine, had to move the transmission mount back a couple of inches to get the T56 in. With the 12 point cage and...
  18. TonyHallo

    Scale Byron Glasair Build

    An engine stand would be great.
  19. TonyHallo

    Scale Byron Glasair Build

    It is a 1971 Vega with a 1996 LT1, T56, Ford 9" rear. I quit flying RC some 21 years ago to build it. I was going real well until I could not find a windshied then lost interest in getting it painted. Found a glass about 9 years ago, logged 2300 street miles since then. It's not a race car.
  20. TonyHallo

    Scale Byron Glasair Build

    The fuselage will be painted like the advertisement from 1986 High Flight magazine. Throw back less the pinstripes.
Top