• If you are new to GiantScaleNews.com, please register, introduce yourself, and make yourself at home.

    We're 1st in Giant Scale RC because we've got the best membership on the internet! Take a look around and don't forget to register to get all of the benefits of GSN membership!

    Welcome!

Recent content by Hazzbro

  1. Hazzbro

    3D 30cc hazzbro extra

    Just remember to glue back in the wedge you cut out of the fuse :)
  2. Hazzbro

    3D 30cc hazzbro extra

    You should use 3/8" tristock (like on the rudder) and center it on the back vertical edge of the fuse.
  3. Hazzbro

    3D 30cc hazzbro extra

    Btw, you can also just make plugs out of balsa and glue them in with a gap filling glue like Gorilla Glue. If you are concerned with strength just double up the back side (inside of the aileron/surface) with another scrap of 3/8" sq. balsa.
  4. Hazzbro

    3D 30cc hazzbro extra

    I add another 3/8" sq. scrap to double the thickness in the hinge area. Just cheap insurance. Gap looks reasonable. Doesn't have to be perfect just close and even.
  5. Hazzbro

    3D 30cc hazzbro extra

    No thrust angle needed. Just mount the engine in square and true to the thrust line. Cover everything, trim off carefully where the glue will be , then glue and square it up. If you don't have the manual let know as I can FTP it to you. Mainly now the only thing you have to do is cut a...
  6. Hazzbro

    3D 30cc hazzbro extra

    Getting ready for a long business trip so my replies will be really slow.... One thing you should do...put all of your tail, ignition, and throttle wires in the fuse now. You can easily cover each side with them taped up in the fuse. Makes life a lot easier! Looking great!
  7. Hazzbro

    3D 30cc hazzbro extra

    In the wing.. :) You really want them there for balance. You can just put a switch and charge jack in one wing. I don't usually put hatches in mine. I use a small lipo for ignition with this: http://www.wrongwayrc.com/index.php?route=product/product&path=73_65&product_id=159 I also use...
  8. Hazzbro

    3D 30cc hazzbro extra

    Velco straps that wrap the tank will work. I use two straps that go through the fuse and wrap the fiji tank front and back. Here's a pic of the wing area I am describing.
  9. Hazzbro

    3D 30cc hazzbro extra

    One question, did you make a lap joint under the d-tube slice in the wing sheeting. I've never built a wing with an edge joint in the d-tube wing sheeting. Maybe others have?
  10. Hazzbro

    3D 30cc hazzbro extra

    Yeah, it mainly happens on the really long cuts on the ply sides...the longer the travel the more a minute travel calibration issue shows up. Built a couple with this and the front anti rotation pin is about all that's off that matters. He pin should be tight. For the amount yours looks off...
  11. Hazzbro

    3D 30cc hazzbro extra

    I have seen this before once when the CNC machine had a travel/calibration error. Easy enough to fix by using the inboard wing rib as a drill template. Just fill the hole with a scrap of balsa then re-drill the hole. If it's not too far off you can just redrill and add a little gorilla glue...
  12. Hazzbro

    3D 30cc hazzbro extra

    Just was directed to this post by one of the Bros on the profilebrotherhood site. I'll certainly help with any questions that I can. I may not respond very fast though due to my work schedule but I'll try as I can. Hazz
  13. Hazzbro

    HazzBro's EEv2 / VVRC 40cc twin

    Fixed it for you. OS rounds up their displacements :). That's my story and I'm sticking to it .
  14. Hazzbro

    HazzBro's EEv2 / VVRC 40cc twin

    Here's another teaser video with a OS 33cc gasser http://youtu.be/L_9a_CRteVs
See more
Top