• If you are new to GiantScaleNews.com, please register, introduce yourself, and make yourself at home.

    We're 1st in Giant Scale RC because we've got the best membership on the internet! Take a look around and don't forget to register to get all of the benefits of GSN membership!

    Welcome!

Search results

  1. AKNick

    The 'What did you do in your workshop tonight?' thread

    The deciding factor for me was: felt good in my hands, I already own Futaba gear so cost effective, touch screen, a receiver with 14 channels or two eight channel rx’s, telemetry, proven, and for me has always been bullet proof. The company makes much more than RC products and can support...
  2. AKNick

    3D Printing General Discussion

    Why the aluminum plate? It wouldn’t fuse to it if that’s what you are asking. But could integrate a recess for the plate Sent from my iPhone using Tapatalk
  3. AKNick

    Who's Up For a 3D Printing Challenge?

    ooof that would take a long time to print. To design it wouldn't be that bad... I think it makes more sense to make one out of wood personally because the time spent printing that size would just take forever (I'm guessing most of the day thus it wouldn't be very cost effective to sell IMHO)...
  4. AKNick

    Discussion The I’m going out flying thread 2018

    Well I finally flew the stupid munk, I mean chip, ur chippy, um super chipmunk! Took nine years as a hangar queen, four engine changes until its first maiden. I had a 2cycle nitro thunder tiger, wanted a four stroke, so I got a saito 72 that ended up in a mojo because I thought it would be too...
  5. AKNick

    The 'What did you do in your workshop tonight?' thread

    New toy! I finally pulled the trigger on upgrading my 8FG to a 18SZ, cost a bunch but I really wanted a touch screen bad - almost got the 16SZ, but it went out of stock... so here I am. Let the programming begin! Sent from my iPhone using Tapatalk
  6. AKNick

    NEW Avios Grand Tundra (unbox and flight test video)

    looks like fun!
  7. AKNick

    The 'What did you do in your workshop tonight?' thread

    Don’t feel like putting that much effort into it. Tried to sell it for the last couple years, nobody wanted it, so I decided to take the engine out, make a dummy spinner, paint a shark mouth, and inspire some kids. My buddy doesn’t have a real war bird hanging in his shop either. If someone...
  8. AKNick

    The 'What did you do in your workshop tonight?' thread

    Hellcat all hung up in my shop with the new face, going to hang it in my buddies LHS probably this week. The TBM is coming together. Pretty much just down to electronics. A little disappointed that the recommended SV1250MG servos, I had to enlarge the servo bays, noticed they get close to...
  9. AKNick

    The 'What did you do in your workshop tonight?' thread

    if you want to get a nice, smooth finish on those tubes, and option is to use a rod dryer that rotates the tube at about 2-9rpm. You can buy the motor and make your own. Just something to think about. I build rods and I have done this to a wing tube before...
  10. AKNick

    Scale 50% Dalotel 165

    Dog must be deaf! lol! sweet engine!
  11. AKNick

    The 'What did you do in your workshop tonight?' thread

    Got some rc goodness from NWRC. 84” turbo bushmaster. Pretty excited to have an electric plane this size to huck around through all four seasons. Let the assembly begin!! Sent from my iPhone using Tapatalk
  12. AKNick

    3D Printing General Discussion

    structurally it would be pretty robust, PLA will melt like every plastic, so what dennis said. Friction as we all well know causes heat, and PLA can melt around 170 degrees. Pretty sure we have all used a starter on a plastic spinner before, the key is positive force not allowing the starter...
  13. AKNick

    3D Printing General Discussion

    Made a dummy spinner roughly 32x45mm, it was hard for me to learn how to hollow out the center correctly, eventually figured it out. I then sanded it and painted it flat black. The plan with this project is to hang the plane on display in my buddies LHS since I can’t even seem to find some one...
  14. AKNick

    3D Printing General Discussion

    Bit of a repost, but my OCD when it comes to organization I decided to post it here too. Had an old brittle throttle arm from an OS FT-120 Gemini that broke. This was my first real 3D printed RC part project. It did not take long, and about 10min to print with 100% infill and PLA. I was...
  15. AKNick

    3D Printing General Discussion

    For those interested I'm going to share my setup and edit this as I go. I'd like to see what everyone else is using to get an idea of what else is out there. Printer: Creality CR-10S 3D Printer Purchased it from GearBest, prices fluctuate quite a bit and there are a lot of coupon codes online...
  16. AKNick

    3D Printing General Discussion

    GSN's place to post 3D printing information and share what everyone is up to in the 3DP world.
  17. AKNick

    The 'What did you do in your workshop tonight?' thread

    Thanks!!!!!
  18. AKNick

    The 'What did you do in your workshop tonight?' thread

    so I am trying to ADD a forum topic in the Technology tab "3D Printing" @GSNadmin ? Doesn't seem like I can, only if I click on an already produce topic can I start a thread. Can you create a new topic 3DPrinting or show me how so I can? Thanks!
  19. AKNick

    The I'm NOT going out flying thread.

    you didn't!!! well its about 20F and white everywhere here... micro snow tornados everywhere because it's blowing about 20mph. Lots of much needed shop time.
  20. AKNick

    The 'What did you do in your workshop tonight?' thread

    I cant figure out how to start a new thread... that must mean it's been too long. help!?!?
Top