• If you are new to GiantScaleNews.com, please register, introduce yourself, and make yourself at home.

    We're 1st in Giant Scale RC because we've got the best membership on the internet! Take a look around and don't forget to register to get all of the benefits of GSN membership!

    Welcome!

Search results

  1. AKNick

    DLE 35RA Muffler bolts

    Can't say that I disagree. My DLE35RA Muffler is a sloppy fit. You can lightly snug up the bolts and you can still move it around pretty good. With that said, the muffler is going to eventually try and wander with all the vibration going on, even under torque. I figure that any way you can...
  2. AKNick

    DLE 35RA Muffler bolts

    I had mine come loose during my 5th gallon. It actually ended up in the cowling after I did a pop-top. You could audibly hear the exhaust note change and feel the loss of power. I had to grab some bolts like you did. One thing I noticed was that the stock threads did not protrude out the...
  3. AKNick

    AJ Laser 230z 73" Build Thread

    Dang, the kid is good. I was impressed with the filmography too. Good find
  4. AKNick

    AJ Laser 230z 73" Build Thread

    AJ 73" Laser 230z Elevator Installation: Just like installing the Rudder, except I did one control surface at a time, starting with the RH surface and joiner. I simply placed the LH surface to maintain alignment. This give you more time to work with the epoxy and alignment as necessary. Once...
  5. AKNick

    AJ Laser 230z 73" Build Thread

    AJ 73" Laser 230z Horizontal Installation: I used some lacing chord, tied a loop on either end, went from the inboard side of the wing tube to the outboard tip of the horizontal, and matched the other side as best I could. I double checked the fit with a ruler by laying it across the leading...
  6. AKNick

    AJ Laser 230z 73" Build Thread

    I personally think this setup is great with just a plain old strait arm at 3" spacing. I think the offset look the best, but not needed for this application. I think people call this "Neutral Ackermann". What you don't want is for the cables to be loose in the neutral position, and get tight as...
  7. AKNick

    AJ Laser 230z 73" Build Thread

    AJ 73" Laser 230z After the rudder is cured, Fire up the RX and make sure your rudder arm is moving in the right direction and that it's as centered as you can get it, now you can attach the control cables up, center the rudder, tighten the cables (I found that the crimps I used slid with a...
  8. AKNick

    AJ Laser 230z 73" Build Thread

    AJ 73" Laser 230z Rudder Attachment: Attached the control horns as I previously mentioned. I used a pin to dub on some petroleum jelly so the epoxy wouldn't get into the hinge itself, most regular people use Vaseline... I just didn't have some on hand so I improvised. Then I proceeded to dub...
  9. AKNick

    AJ Laser 230z 73" Build Thread

    AJ 73" Laser 230z I personally don't really like the crimp quality of the included crimps, so I went with the 15-45lb Berkley fishing line crimps. I used two for insurance, they feel 1000 times better IMHO than their counterparts. If you were to buy new line, I'm guessing it's 45lb or so? I...
  10. AKNick

    AJ Laser 230z 73" Build Thread

    AJ 73" Laser 230z Okay, so this is where I don't want to scare or shy away anybody from either products. So read before you judge any picture by itself. Just sharing my research - take it or leave it. Servo Tray Failure by another a laser 73" owner who essentially had lightly crashed/hard...
  11. AKNick

    AJ Laser 230z 73" Build Thread

    AJ 73" Laser 230z I got my SAVOX SV-1270TG Servos from Code3 Innovations. You can PM him on FG or visit his website. Dimensions(mm): 40.3x20.2x37.2 Weight(g): 56 Speed(@6.0V sec/60): .14 Torque(@6.0V oz-in): 361.1 Speed(@7.4V sec/60): .11 Torque(@7.4V oz-in): 487.1 Gear: Titanium &...
  12. AKNick

    AJ Laser 230z 73" Build Thread

    AJ 73" Laser 230z Microballooning it up: A shot sized cup would be a better method for this FYI. It'll keep the glass balloons from going all over the place.
  13. AKNick

    AJ Laser 230z 73" Build Thread

    AJ 73" Laser 230z Control Horn Installation. As you can tell, I scuffed up the lower section pretty good of the control horn along with the underbelly of the plate with some sand paper just like the elevator joiner.. I even made a few notches with my dremel just cuz, heck it probably lowered...
  14. AKNick

    AJ Laser 230z 73" Build Thread

    AJ 73" Laser 230z :thumbup:
  15. AKNick

    AJ Laser 230z 73" Build Thread

    I used these from Redwing RC (they come in pairs): Elevator - SS-PR-110 (140mm OAL) Ailerons - SS-PR-30 (55mm OAL) http://www.redwingrc.com/index.php?main_page=product_info&cPath=3_6_38&products_id=91 I found that these push rods use up most of the threads with a bit to spare. I just...
  16. AKNick

    AJ Laser 230z 73" Build Thread

    It's hard to find any aftermarket servo arms that support the Mfgrs ball link ID. The Mfgrs ball links have a smaller OD so they can fit inside the control horn slots, and you can use the servo arms that cam with the servo and wouldn't have to auger out a huge 4-40 hole. I essentially bought new...
  17. AKNick

    AJ Laser 230z 73" Build Thread

    Makes perfect sense! I've always marked with a pencil and just cut inside the box I made. I like what you are saying about lifting up the horn plate, and using it as a guide as you cut. I usually have enough white ultracote laying around to cover my roof, that stuff is handy. Makes sense to save...
  18. AKNick

    AJ Laser 230z 73" Build Thread

    AJ 73" Laser 230z Horizontal Stab and Elevator: Since I am using one elevator servo, I will be joining the elevator halves together. Doing this, insert the hinges, and joiner, mark the edge with a pencil, remove, scruff the joiner with a fine sandpaper and finish it off with a coarse piece of...
  19. AKNick

    AJ Laser 230z 73" Build Thread

    AJ 73" Laser 230z Sometimes when you get an ARF you need to make it your own. So naturally you modify it a bit, right? I personally like how the stars on this ARF resemble the scale feature of the original Laser Aircraft. SO at no disregard of the mfgr's original color scheme, which actually...
  20. AKNick

    AJ Laser 230z 73" Build Thread

    I've used Spot on RC V1 servo arms on the ailerons of my 71 slick, and found one that came loose during my preflight. I always use blue locktite, maybe just me, that's why I went with the MPI's... but on the SAVOX servos I had to ream out the hold down screw hole. I could guess this is why...
Top