• If you are new to GiantScaleNews.com, please register, introduce yourself, and make yourself at home.

    We're 1st in Giant Scale RC because we've got the best membership on the internet! Take a look around and don't forget to register to get all of the benefits of GSN membership!

    Welcome!

Search results

  1. Tseres

    Dual BuildNew PAU 35cc Edge and 35cc Extra

    I got all the tape off of the Extra. But put another piece on the counterbalance to hold the ruder in place. Mounted the ruder servo and finished the Elevator push rods. The end caps are glued on with 30 minute epoxy and I have a #2 sheet metal screw to insure that they don't pull apart. The...
  2. Tseres

    Dual BuildNew PAU 35cc Edge and 35cc Extra

    Back to the Edge today. Got all the tape off and cleaned off the glue from the hinges on the wings. Everything is nice and free. Mounted the servos and set up the linkage. The aluminum servo arms are on the way for the Edge, but not here yet so I used some plastic arms for setup. The tip for...
  3. Tseres

    Dual BuildNew PAU 35cc Edge and 35cc Extra

    I don't know the specks on that servo. I did mention that you can use full size servos. You can open up the cutout for them to fit. There is plenty of reinforcement to let that happen.
  4. Tseres

    Dual BuildNew PAU 35cc Edge and 35cc Extra

    Finished gluing the hinges and set it on the floor to let it cure overnight. Took the tape off the ruder and elevator hinges of the Edge. Picked out the excess glue. There was very little to pick out cause most of it came off with the masking tape.The next step I think should be the pull pull...
  5. Tseres

    Dual BuildNew PAU 35cc Edge and 35cc Extra

    It's just you. It's how the way they are sitting on the table.
  6. Tseres

    Dual BuildNew PAU 35cc Edge and 35cc Extra

    I spent this afternoon on the Extra. So far I have the covering shrunk. All the control horns glued in. The hinge pins on the stab and vertical fin are epoxied in. Jusrt a couple of things of interest. On the Extra I had tocut one step off of the bottom of the control horns for the Elevator to...
  7. Tseres

    Dual BuildNew PAU 35cc Edge and 35cc Extra

    Yes. most of the time. I may show a different way on the Extra. Don't know yet. Stay tuned.
  8. Tseres

    Dual BuildNew PAU 35cc Edge and 35cc Extra

    Thanks. And Thanks for following.
  9. Tseres

    Dual BuildNew PAU 35cc Edge and 35cc Extra

    Finished up gluing the hinges this morning on the Edge. I use Foaming Gorilla Glue for that. I use a Q-Tip to moisten the wood with water. The water helps the G-Glue set off. The glue expands as it foams so you have to make sure you tape it up real good so the foaming don't push the hinge out of...
  10. Tseres

    Scale Balsa USA Camel F1

    I put the plane up on the pegs for a few weeks while I finish My 35cc Builds. As soon as I get finished with them I'll get back to this. If you want something to do meanwhile look in here. http://giantscalenews.com/threads/dual-buildnew-pau-35cc-edge-and-35cc-extra.4295/page-3#post-93546
  11. Tseres

    Dual BuildNew PAU 35cc Edge and 35cc Extra

    Thanks. I learned a lot of my stuff from other people. Terry is the one I learned the tape and heating up the Vaseline in a bottom of a pop can. The hole punch came out of nescessity. I had the puncher. I think the other guys are using a hand held punch. They both work.
  12. Tseres

    Dual BuildNew PAU 35cc Edge and 35cc Extra

    Today was "Mess Up Day". I cut the covering on the top of the aileron for the hinge points. No.No.No. That is not what your supposed to do. Only the bottom of the ailerons get cut open. I had to patch the top of the ailerons. When you get to building yours. Remember my mess up and don't do like...
  13. Tseres

    Dual BuildNew PAU 35cc Edge and 35cc Extra

    Not yet but I will.
  14. Tseres

    Dual BuildNew PAU 35cc Edge and 35cc Extra

    Thanks Guys. Lets just leave it at that.
  15. Tseres

    Dual BuildNew PAU 35cc Edge and 35cc Extra

    I mounted the DA35 on the Extra today. Just roughed out the Cowl to let the engine fit without binding. Mounted the tail gear on both planes. These get mounted with Wood screws so don't forget to harden the screw hole with thin CA. Started working on the ruder. Cut out the covering and trial...
  16. Tseres

    Dual BuildNew PAU 35cc Edge and 35cc Extra

    I was Questioned about my affiliation with PAU Yesterday. Here it is in a nutshell. I'm very good friends with Herve the owner of PAU. We talk on the phone on an average of 3 times a week. I am not sponsored by him. I pay full price for my planes. I do help him out at the XFC and Joe Nall as...
  17. Tseres

    PAU Owners Thread

    35cc Build thread here: http://giantscalenews.com/threads/dual-buildnew-pau-35cc-edge-and-35cc-extra.4295/
  18. Tseres

    Dual BuildNew PAU 35cc Edge and 35cc Extra

    I've built so many of these Extras and Edges that its become second nature to build them. It's a good thing cause there are no manuals for these yet. Didn't hardly take any time to rough out the Cowl and mount the engine on the Edge. Good news is that the stock DLE standoffs fit almost perfect...
  19. Tseres

    Dual BuildNew PAU 35cc Edge and 35cc Extra

    $475
  20. Tseres

    Dual BuildNew PAU 35cc Edge and 35cc Extra

    I've been waiting to build one of these planes for 5 yrs. That was when I first discussed with Herve that he needed smaller planes. He shut it down. He said that his business was Giant Scale Planes and that was where he will concentrate his efforts. I heard what he said but kept after him about...
Top