• If you are new to GiantScaleNews.com, please register, introduce yourself, and make yourself at home.

    We're 1st in Giant Scale RC because we've got the best membership on the internet! Take a look around and don't forget to register to get all of the benefits of GSN membership!

    Welcome!

Search results

  1. TonyHallo

    Scale RCM 1/3 Scale Champ Build

    Woke up this morning and got the door hinges epoxied in before the grandsons arrived. Cutting hinge slots in spruce is a pain in the behind. They are not perfect but the door opens and closes without rubbing. Need to make the latch mechanism now.
  2. TonyHallo

    Scale RCM 1/3 Scale Champ Build

    Moment of truth, put the wings on the fuselage today to check alignment, the diagonals were within 3/16" which is close enough, will get it dead nuts with the lift struts, actually the wing tips move quite a bit, had to anchor the measuring tape at the rudder post to get accurate measurement.
  3. TonyHallo

    Scale RCM 1/3 Scale Champ Build

    Last year I was able to get a 5000# vibratory asphalt roller to roll our field, I hope to secure it again this year. It took about 3 hours to roll the field, then I took it home and did my yard so the grandsons wouldn't break their ankles. Plan to do so again. Did you get what you needed at...
  4. TonyHallo

    Scale RCM 1/3 Scale Champ Build

    Was out late last night and went flying this morning. Flew the Cherokee three times today, first flights of 2019, all in all a good day just not a very productive day. The field is rough as *ell, needs rolled in the worst way. Got the cabin rear wall installed and made the door. Not sure how...
  5. TonyHallo

    IMAC Pattern - Cadence w/ DA 35

    Mine is spelled Miler Lite!
  6. TonyHallo

    Scale RCM 1/3 Scale Champ Build

    Thanks. How did you do at Toledo? It's getting smaller every year! This is what I found for the Champ, http://www.truturn.com/cgi-bin/store/agora.cgi?p_id=tth2500bcu:110&ppinc=prophubs110&exact_match=on. Didn't know that TruTurn made Cub Hubs, glad I stopped and asked. It will good nice on...
  7. TonyHallo

    Scale 1/3 Scale Extra 330L Build.

    Looks like a tight squeeze? My Cherokee is like that.
  8. TonyHallo

    IMAC Pattern - Cadence w/ DA 35

    Did you have gravy with your epoxy mashed potatoes?
  9. TonyHallo

    Scale RCM 1/3 Scale Champ Build

    Installed the vertical fin and tail wheel today, also continued to add parts to the cabin area. Still have a few more filler pieces to install before the 1/32" skins are installed. Heading to Toledo in the morning so nothing will get done except parting with some cash.
  10. TonyHallo

    Scale RCM 1/3 Scale Champ Build

    Well Snoops got to use the drum sander to sand the filler pieces for the rear windows, the back wall also glues to these pieces. My scrap balsa drawer is overflowing so I decided to laminate some 3/16" scrap for these pieces. Put the 3" drum on for this operation.
  11. TonyHallo

    Scale RCM 1/3 Scale Champ Build

    Got out the makeshift router table and put the radius on the rudder edges. The rudder is 1/2" thick, the 1/4" radius bit was just the ticket. I also used the router to put the radius on the front posts in the cabin. The drawing calls out 3/8" x 5/8" half round, I had no idea what in world it...
  12. TonyHallo

    Scale RCM 1/3 Scale Champ Build

    Got the four front posts installed along with the rear diagonal dowels. The post are inset about 9/16" at the top from the rib formers. The post are lapped glued to the spar boxes. Once the glue dries overnight, the craddle will be removed.
  13. TonyHallo

    Scale RCM 1/3 Scale Champ Build

    I have the cabin roof roughed in. From the photo above the trailing edges are screwed to the vertical former with # 2 servo screws, a cradle was made from scrap wood to support the roof at the desired incidence of +1 degree. Once the glue dries, I'll lay the fuselage on it's side and align the...
  14. TonyHallo

    Scale RCM 1/3 Scale Champ Build

    It is one of those things you can do without but nice to have. The spindle moves up and down when it runs. There are several sizes of drums from 2" to 5/8". I have a 12" disc sander that is used every day, not so for the drum sander. I would put the drum sander and scroll saw in the same...
  15. TonyHallo

    Scale RCM 1/3 Scale Champ Build

    .060" diameter, phillips head. Managed to get the rear formers installed in between watching the grandsons, actually the two year was helping this morning when his brother was in preschool. The cabin roof will go on next, set the wing incidence and fill in the vertical sticks that hold the...
  16. TonyHallo

    Scale RCM 1/3 Scale Champ Build

    The fabric on the Champ is screwed to ribs rather than stitched. The full scale uses #4 screws.
  17. TonyHallo

    Scale RCM 1/3 Scale Champ Build

    I found a 4 1/2" carbon fiber spinner at the MARC's RC auction on Saturday, $20, couldn't pass it up. Sounds like you will be hitting the Micro Fastener booth, I plan to do so as well, still need a couple hundred on #0 screws for the wings. I have about 1000 already, can't wait to put these...
  18. TonyHallo

    Scale RCM 1/3 Scale Champ Build

    Thank you, I am enjoying this build, makes me want to get out of bed early. Don't buy everything, leave something for me!!!
  19. TonyHallo

    Scale RCM 1/3 Scale Champ Build

    The grandsons were here today, not much work done. They do keep you moving. Did manage to get four formers cut out tonight after dinner. Once these are installed then the cabin roof will be installed, then the dash, then sheet interior with 1/32" plywood that I need to order.
  20. TonyHallo

    Scale RCM 1/3 Scale Champ Build

    What day are you going to Toledo? I hope to be there on Saturday.
Top